New Stuff on it's way - Part 2.

[Wolfman]

Ok, as a few of you now, i have spent the last few months modding my bike, well tomorrow morning my bike goes back to the shop for over a week for basically what is the second round of mods, and by the time this lot is done, i am pretty much done modding this bike.

So with this in mind, a thought a new thread would be a good way to bring the project up to speed, and lay out what is going on the bike now.

Ok basically till now i have put on a BMC air filter, a PCIII, custom mapped, a set of TB Ti's, Ohlins rear shock, Racetech fork springs, and gold valve emulators, Goodridge braided lines - front & back, Braking Wave discs - front, Ferodo sintered brake pads, front & back, MCS drag Bars, Carbon Bar ends, MCS mini carbon look indicators, and lots of other cosmetic things, like indicators, mirrors, tank bra, and a bit of painting.

There is still a few things left hanging from round one, like i have not had the PCIII re-mapped since getting the TB cans, i still have not got my -2 front sprocket, which is on back order, and as such have still not installed the speedohealer i have sitting waiting for me at the shop.

Now for round 2 on the "performance" mods. This time it is starting because the wheels come off tomorrow morning to be polished, which will be out for about a week. So when the wheels get back, i am hopefully fitting the following if it has all arrived.

Braking Wave disc to replace the rear OEM brake rotor.
YA44RIDg.jpg

Valter Moto type 2 rearsets - black (shown in red here) + reverse shift pattern shift rod.
PE_2_rossa.jpg

Pazzo shorty levers - black
pazzo_blackblack.jpg

04 R6 4 spot monoblock left & right front brake calipers.
24a3_1.jpg

-2 (14t) Vortex front sprocket..if it finally arrives! & Speedohealer.
08 FZ6 forks
08 FZ6 front fender - black
Racetech springs, and gold valve emulators to be transfered into 08 FZ6 forks
Dyno tune re-map to take into account the TB pipes.
dropping forks a further 5mm through the triple clamps, stiffening of rear & front suspension.
Install of alarm, with full remote monitoring & text alerts.

Once all this is done, the project is pretty much complete except for a Puig Bellypan, and Ermax seat Cowl i have on order, and maybe a steering damper, although front has stopped wobbling at hig speed since i modded forks, and dropped them 15mm through the triple clamps. Only other thing might be a 520 chain conversion...but that can wait till i wear out the present sprockets.

Will post lots of photo's when all this is done..., including a scanned copy of the long overdue dyno re-map.

I'm off for a ride while i have the chance.

[Ozfazer6]

Sounds good Jamie .I will be interested on yourfeed back about the front sprocket as I am seriously considering going -1 on the front with healer .

[sideshow_downs]

Sounds like you have a few good mods planned. Keep us posted on how it all works out

[Rxticle]

Originally Posted by Wolfman

Ok, as a few of you now, i have spent the last few months modding my bike, well tomorrow morning my bike goes back to the shop for over a week for basically what is the second round of mods, and by the time this lot is done, i am pretty much done modding this bike.

LOL - heard that before. The only time you finish modding is when you sell for your next project.

[Wolfman]

Originally Posted by Rxticle

LOL - heard that before. The only time you finish modding is when you sell for your next project.

Mate there is not much i can do after this lot! apart from Carbon Wheels!

[aussiejules]

Time will tell the itch isnt going to leave you. helmet lock,08 cluster,different seat, tank grips, flashing lights on your tyre valves, 250 rear tyre, fz1 motor, machine guns, smoke screen, but honestly i told you on the weekend im jealous, shes looking great.

[Wolfman]

Originally Posted by aussiejules

Time will tell the itch isnt going to leave you. helmet lock,08 cluster,different seat, tank grips, flashing lights on your tyre valves, 250 rear tyre, fz1 motor, machine guns, smoke screen, but honestly i told you on the weekend im jealous, shes looking great.

FZ1 motor.....Lol! as long as a could stil register and insure it as a 600!, 250 rear tyre, would handle like a harley! fashing lights on the tyre valves...that's just ghetto! tank grips...will leave that for you, helmet lock...after using matt's on the weekend, it would be a sensible mod...just how, bit of welding to the seat rails maybe, 08 cluster, no thanks, like the gawdy round thing that sits off centre on my 06, different seat, oh i would like a bagster seat, but they are silly expensive, and i dont have an issue with the comfort of the OEM seat.

[aussiejules]

Just trying to give you ideas, i especially like the smoke screen one. Axle sliders, 08 swingarms,a bolt to put in that hole in the motor (can you ask them at yam what it was for) intergrated tail light, tank camera bracket, radar detector,

[Wolfman]

Originally Posted by aussiejules

Just trying to give you ideas, i especially like the smoke screen one. Axle sliders, 08 swingarms,a bolt to put in that hole in the motor (can you ask them at yam what it was for) intergrated tail light, tank camera bracket, radar detector,

Yes the Smoke screen is very Batman! Would be a laugh. Axle Sliders is not a silly idea, was looking at these the other day, not a fan of integrated tail lights, tank camera...god no...evidence! 08 swing arm, sexy, but not really an issue for me....and as for that hole in the motor, yes i must ask, what's the bet they dont know either?

Radar detector...i dont speed....much....lol! where would i hide it on a naked?

[Discofrank]

why add the emulators to a set of forsk with adjustable settings?